MICROHARDNESS OF TOOTH ENAMEL WITH DIFFERENT LEVEL OF RESISTANCE

  • N.L. Chukhray Danylo Halytskiy Lviv National Medical University
  • V.A. Vynar Physics and Mechanics Institute by G.V. Karpenko of National Academy of Sciences of Ukraine
Keywords: enamel microhardness, resistance, permanent teeth.

Abstract

This study about the microhardness of tooth enamel is evaluated by nanoidentation. The data indicate that the average microhardness of the enamel of the permanent teeth in the region of the equator is 5,75±0,06 Gpa, modulus of elasticity - 97,72±0,74 GPa on average data. It was revealed difference in indices of enamel microhardness, depending on the level of its enamel. Microhardness cariesresistant enamel of the permanent teeth is 7,85±0,10 GPa, which is higher than the corresponding mean for microhardness of relatively resistant enamel 6,45±0,06 GPa and significantly higher than caries susceptible enamel (2,95±0,22 GPa ). The relationship between enamel resistances with microhardness of its superfacial layers is showed. The highest mean of elasticity was found in samples of teeth with enamel resistant to dental caries (119,77±1,30 GPa), which is on 10,54% and 44,67% higher compared with the value of the index in samples of tooth with conditionally resistant and caries susceptible enamel.

The received data make it possible to assume that the modulus of elasticity of enamel of permanent teeth also depends on the enamel resistance. Therefore, in order to prevent the injuring of hard tissues of caries susceptible enamel is advisable to appoint mineralizing means that can increase the microhardness (caries resistance) of teeth.

Downloads

Download data is not yet available.

References

1. Вивчення мікротвердості емалі та дентину різців у нормі і при патологічних станах / [Є.В. Ковальов, М.А Шундрик, Л.С. Шундрик, В.С. Амосова] // Український стоматологічний альманах. – 2012. - №3. – С. 1-7.
2. Головин Ю.И. Наноиндентирование и механические свойства твердых тел в субмикрообъемах, тонких приповерхностных слоях и пленках (обзор) // Физика твердого тела.-2008.-Т.50, вып.12.-С.2116-2142.
3. Загорский В.А. Плотность твердых тканей / В.А. Загорский, И.М. Макеева, В.В. Загорский // Российский стоматологический журнал. – 2012. - №2. – С. 29-31.
4. Исследование механических свойств твердых тканей зуба методом наноидентирования / С.Н. Дуб, А.В. Борисенко, К.Е. Печковский [и др.] // Современная стоматология. – 2008. - №1(41). – С. 25-29.
5. Окушко В.Р. Методика выделения диспансерных групп школьников на основе донозологической диагностики кариеса / В.Р. Окушко, Л.И. Косарева // Стоматология. – 1983. - №6. – С. 8-10; Окушко В.Р.,1985.
6. Ремизов С.М. Определение микротвердости для сравнительной оценки зубной ткани здоровых и больных зубов человека / С.М. Ремизов // Стоматология. – 1965. - №3. – С. 33-37.
7. Ремизов С.М. Особенности развития кариеса в фиссурах зубов по данным микротвердости. Диагностика, лечение, профилактика кариеса зубов/ С.М. Ремизов, Л.В. Звонникова, Н.А. Районов // Стоматология. – 1995. - №1. – С. 9-11.
8. Сороченко Г.В. Вивчення механічних властивостей емалі постійних зубів у період вторинної мінералізації методом наноідентування / Г.В. Сороченко // Вісник наукових досліджень.- 2015. - №4. – С. 81-83.
9. Ярова С.И. Анализ показателей микротвердости эмали при различном состоянии твердых тканей и глубины микротрещин / С.И. Ярова, И.И. Заболотна // Запорожский медицинский журнал. – 2013. - №4(79). – С. 117-120.
10. Ionescu C. Nanomechanical properties of dental surfaces study as an irradiated treatment simulation / C. Ionescu, M.V. Perieanu, L.S. Craciun // Romanian Reports in Physics. – 2016. - Vol. 68, No. 2. - P. 693–701.
11. Kan Q. Oliver–Pharr indentation method in determining elastic moduli of shape memory alloys—A phase transformable material / Q. Kan, W. Yan, G. Kang // Journal of the Mechanics and Physics of Solids. - 2013. – V. 61. – P. 2015–2033.
12. Milman Yu. Plasticity characteristic obtained through instrumental indentation /Yu. Milman, S. Dub, A. Golubenko // Mater. Res. Symp. Proc. — 2008. —1049. — P. 734—743.
13. Oliver W. C. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation measurements / W. C. Oliver, G. M. Pharr // J. Mater. Res. — 1992. — 7, Nо. 6. — P. 1564—1583.
14. Review of research on the mechanical properties of the human tooth / [Y.R. Zhang, W. Du, X.D. Zhou, H.Y. Yu] // International Journal of Oral Science. – 2014. - №6. – Р. 61–69.
Published
2018-03-21
How to Cite
Chukhray, N., & Vynar, V. (2018). MICROHARDNESS OF TOOTH ENAMEL WITH DIFFERENT LEVEL OF RESISTANCE. Ukrainian Dental Almanac, (3), 5-9. Retrieved from https://dental-almanac.org/index.php/journal/article/view/272
Section
EXPERIMENTAL-THEORETICAL SECTION